Difference between revisions of "Jenny corexy voron V1.2 mainpage"
Warriorlious (talk | contribs) |
Warriorlious (talk | contribs) |
||
Line 64: | Line 64: | ||
Insert pressure_advance value in printer.cfg. | Insert pressure_advance value in printer.cfg. | ||
JENNY COREXY BGM extuder pressure_advance = 0.046 about. | JENNY COREXY BGM extuder '''pressure_advance = 0.046''' about. | ||
more info see [https://github.com/KevinOConnor/klipper/blob/afca515e2c2db240b4d354a0ae665479894ef89b/docs/Pressure_Advance.md Klipper pressure] | more info see [https://github.com/KevinOConnor/klipper/blob/afca515e2c2db240b4d354a0ae665479894ef89b/docs/Pressure_Advance.md Klipper pressure] | ||
---- | ---- | ||
====speed tune==== | ====speed tune==== | ||
Modify these speed values to make the printer faster while maintaining quality. | Modify these speed values to make the printer faster while maintaining quality. |
Revision as of 16:12, 17 August 2021
Overview
this is mainpage of jenny corexy 3d printer V1.2
jenny corexy is a metallized structure inspire by vorondesign voron2.4.
we use a more stable 4040 extrusions frame,but keep 2020 extrusions as gantry let it not too heavy. The gantry use a 9mm widened belt,to keep a bigger print size. Also expanded the width of the linear rails.
All structural part use aluminum sheet with stainless steel column let printer can stable in high temperature environment.But some of the beautiful parts that don't matter are whit 3D printed.
I also modified the leveling probe, using a structure I named JennyTouch. It is a contact type photoelectric sensor mechanism,can probe aluminum 、PEI、 glass and any solid platform.
Resources
Communication
- discuss (trouble shooting and feature suggestions)
- facebook (assembly show and printing show)
- youtube (Serial Request and development show)
- discord (timely communication)
Brief assembly instructions
preparatory work
Attention
setup firmware
Debugging
PID
use this command to calibrate hotend pid:
PID_CALIBRATE HEATER=extruder TARGET=220
And this command to calibrate bed pid:
PID_CALIBRATE HEATER=heater_bed TARGET=60
when finished will have some information like this:
PID parameters: pid_Kp=18.731 pid_Ki=0.827 pid_Kd=106.065 The SAVE_CONFIG command will update the printer config file with these parameters and restart the printer.
Use this PID value in printer.cfg
more info see Klipper PID calibrate.
Calibrate extruder pressure
Prepare for the test by issuing the following G-Code command:
SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=1 ACCEL=500
This command makes the nozzle travel slower through corners to emphasize the effects of extruder pressure. Then for printers with a direct drive extruder run the command:
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=0.005
After that,print this gcode: square_tower_test.gcode
The pressure_advance value can then be calculated as pressure_advance = <start> + <measured_height> * <factor>. (For example, 0 + 12.90 * .005 would be 0.0645.)
Insert pressure_advance value in printer.cfg.
JENNY COREXY BGM extuder pressure_advance = 0.046 about.
more info see Klipper pressure
speed tune
Modify these speed values to make the printer faster while maintaining quality.
- In section [printer]:
max_velocity: 200 max_accel: 6000 max_z_velocity: 10 max_z_accel: 200
- In section [stepper_n]:
homing_speed: 130
- In section [extender]:
max_extrude_only_velocity:100 max_extrude_only_accel:3000
- in section [probe]:
speed: 80.0
- In section [quad_gantry_level]:
speed: 120